Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 866 views

    Sa-240 Asme Sec.2

    Uploaded by

    arianaseri
    SPECIFICATION FOR CHROMIUM AND CHROMIUM NICKEL STAINLESS STEEL PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS AND FOR GENERAL APPLICATIONS

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Sa-240 Asme Sec.2

    Uploaded by

    arianaseri
    866 views1 page
    SPECIFICATION FOR CHROMIUM AND CHROMIUM NICKEL STAINLESS STEEL PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS AND FOR GENERAL APPLICATIONS

    Original Title

    SA-240 ASME SEC.2

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    SPECIFICATION FOR CHROMIUM AND CHROMIUM NICKEL STAINLESS STEEL PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS AND FOR GENERAL APPLICATIONS

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    866 views1 page

    Sa-240 Asme Sec.2

    Uploaded by

    arianaseri
    SPECIFICATION FOR CHROMIUM AND CHROMIUM NICKEL STAINLESS STEEL PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS AND FOR GENERAL APPLICATIONS

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    2011a SECTION II, PART A

    SA-240/SA-240M

    SPECIFICATION FOR CHROMIUM AND CHROMIUMNICKEL STAINLESS STEEL PLATE, SHEET, AND STRIP FOR PRESSURE VESSELS AND FOR GENERAL APPLICATIONS
    SA-240/SA-240M

    (Identical with ASTM Specication A 240/A 240M-04)

    1.

    Scope 1.1 This specication covers chromium, chromiumnickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specication. 1.3 This specication is expressed in both inch-pound and SI units. However, unless the order species the applicable M specication designation (SI units), the material shall be furnished in inch-pound units.

    3.

    General Requirements 3.1 The following requirements for orders for material furnished under this specication shall conform to the applicable requirements of the current edition of Specication A 480/A 480M. 3.1.1 Denitions, 3.1.2 General requirements for delivery, 3.1.3 Ordering information, 3.1.4 Process, 3.1.5 Special tests, 3.1.6 Heat treatment, 3.1.7 Dimensions and permissible variations, 3.1.8 Workmanship, nish and appearance, 3.1.9 Number of tests/test methods, 3.1.10 Specimen preparation, 3.1.11 Retreatment, 3.1.12 Inspection, 3.1.13 Rejection and rehearing, 3.1.14 Material test report, 3.1.15 Certication, and 3.1.16 Packaging, marking, and loading.

    2.

    Referenced Documents 2.1 ASTM Standards: A 370 Test Methods and Denitions for Mechanical Testing of Steel Products A 480/A 480M Specication for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip A 923 Test Methods for Detecting Detrimental Intermetallic Phase in Wrought Duplex Austenitic/Ferritic Stainless Steels E 112 Test Methods for Determining Average Grain Size E 527 Practice for Numbering Metals and Alloys (UNS) 2.2 SAE Standard: J 1086 Practice for Numbering Metals and Alloys (UNS)
    365

    4.

    Chemical Composition 4.1 The steel shall conform to the requirements as to chemical composition specied in Table 1, and shall conform to applicable requirements specied in Specication A 480/A 480M.

    You might also like