Nothing Special   »   [go: up one dir, main page]
Sharp 13VT-N100 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. TV VCR Combo
  5. 13VT-N100
  6. Service manual

Sharp 13VT-N100 Service Manual

Tv/vcr combination
Hide thumbs
Table of Contents

Advertisement

Quick Links

In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
» IMPORTANT SERVICE SAFETY PRECAUTION ............................................................................ 2
» ELECTRICAL SPECIFICATIONS .................................................................................................... 6
» LOCATION OF USER'S CONTROL ................................................................................................ 7
» DISASSEMBLY AND REASSEMBLY .............................................................................................. 9
» INSTALLATION AND SERVICE INSTRUCTIONS ......................................................................... 12
» PRECAUTIONS IN REASSEMBLING ........................................................................................... 17
» FUNCTION OF MAJOR MECHANICAL PARTS ........................................................................... 18
» ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY ............................................................ 40
» TROUBLESHOOTING ................................................................................................................... 42
» CHASSIS LAYOUT ........................................................................................................................ 54
» BLOCK DIAGRAM OF TV SECTION ............................................................................................ 56
» BLOCK DIAGRAM OF VCR SECTION ......................................................................................... 58
» OVERALL SCHEMATIC DIAGRAM ............................................................................................... 68
» DESCRIPTION OF SCHEMATIC DIAGRAM ................................................................................. 70
» PRINTED WIRING BOARD ASSEMBLIES ................................................................................... 82
» REPLACEMENT PARTS LIST ....................................................................................................... 86
» PACKING OF THE SET ............................................................................................................... 103
SHARP CORPORATION
SERVICE MANUAL
TV/VCR COMBINATION
Chassis No. B99B
MODELS
CONTENTS
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
1
13VT-N100
13VT-N150
13VT-CN10
13VT-N100
13VT-N150
13VT-CN10
SY9U113VTN100
Page

Advertisement

Table of Contents
loading

Related Manuals for Sharp 13VT-N100

Summary of Contents for Sharp 13VT-N100

  • Page 1: Table Of Contents

    13VT-N100 13VT-N150 13VT-CN10 SERVICE MANUAL SY9U113VTN100 TV/VCR COMBINATION Chassis No. B99B 13VT-N100 13VT-N150 13VT-CN10 MODELS In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its original condition and only parts identical to those specified should be used.

  • Page 2: Important Service Safety Precaution

    13VT-N100 13VT-N150 13VT-CN10 IMPORTANT SERVICE SAFETY PRECAUTION Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines which follow: WARNING X-RADIATION AND HIGH VOLTAGE LIMITS 1. For continued safety, no modification of any circuit 1.

  • Page 3: Safety Notice

    13VT-N100 13VT-N150 13VT-CN10 IMPORTANT SERVICE SAFETY PRECAUTION (Continued) » Connect the resistor connection to all exposed metal BEFORE RETURNING THE RECEIVER parts having a return to the chassis (antenna, metal (Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage...
  • Page 4 13VT-N100 13VT-N150 13VT-CN10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION 1.
  • Page 5 13VT-N100 13VT-N150 13VT-CN10 PRECAUTIONS A PRENDRE LORS DE LA REPARATION (Suite) » Toucher avec la sonde d'essai les pièces métalliques VERIFICATIONS CONTRE L'INCEN-DIE ET exposées qui présentent une voie de retour au LE CHOC ELECTRIQUE châssis (antenne, coffret métallique, tête des vis, Avant de rendre le récepteur à...

  • Page 6: Electrical Specifications

    13VT-N100 13VT-N150 13VT-CN10 ELECTRICAL SPECIFICATIONS TV SECTION POWER INPUT: 120 V AC 60 Hz POWER RATING: 65 W PICTURE SIZE Width: 37.8 cm Height: 38.7 cm Depth: 38.2 cm CONVERGENCE: Magnetic SWEEP DEFLECTION: Magnetic FOCUS: Hi-Bi-Potential Electrostatic INTERMEDIATE FREQUENCIES Picture IF Carrier Frequency: 45.75 MHz...

  • Page 7: Location Of User's Control

    13VT-N100 13VT-N150 13VT-CN10 LOCATION OF USER'S CONTROL Description Of Controls FRONT TV • VCR COMBINATION POWER POWER/ WAKE-UP PROGRAM TIMER TAMPER TIMER PROOF POWER button SENSOR AREA FOR REMOTE CONTROL VIDEO/AUDIO Input Jacks POWER/ WAKE-UP PROGRAM TAMPER TIMER TIMER PROOF...

  • Page 8: Remote Control Battery Installation

    13VT-N100 13VT-N150 13VT-CN10 LOCATION OF USER'S CONTROL (Continued) Location Of Control’s Buttons (Remote Control) Infrared Transmitter Window INPUT DISPLAY TV/VIDEO Select • Used to change the On Screen Display. POWER ON/OFF MUTE Press Mutes sound. CHANNEL SELECT POWER Press again...

  • Page 9: Disassembly And Reassembly

    13VT-N100 13VT-N150 13VT-CN10 DISASSEMBLY AND REASSEMBLY 1. Remove the 7 rear cover fixing screws and detach the rear cover. 2. Take out the anode cap, CRT PWB, connectors K and M, coating earth, Speaker chip fixing screws and others. 3. Take out the main PWB unit and the VCR unit.
  • Page 10 13VT-N100 13VT-N150 13VT-CN10 DISASSEMBLY AND REASSEMBLY (Continued) 5. Remove the 4 cassette housing control fixing screws, and detach the cassette housing control. 6. Remove the 2 mechanism chassis angle fixing screws, and remove the 1 head amp shielding case fixing screw.
  • Page 11 13VT-N100 13VT-N150 13VT-CN10 DISASSEMBLY AND REASSEMBLY (Continued) For servicing any of the components inside, disconnect the lead dressing holder. Position the main PWB unit upright as shown below and connect the leads for starting the services. FRONT...

  • Page 12: Installation And Service Instructions

    13VT-N100 13VT-N150 13VT-CN10 INSTALLATION AND SERVICE INSTRUCTIONS Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic screwdriver or TV alignment tools. (2) Before performing adjustment, TV set must be on at least 15 minutes. CIRCUIT PROTECTION HIGH VOLTAGE CHECK The receiver is protected by a 4.0A fuse (F701), mounted...

  • Page 13: Service Mode

    13VT-N100 13VT-N150 13VT-CN10 The N-series SHARP TV/VCR COMBINATION have most of the analog setup adjustments eliminated. Coil and variable resistor adjustments are now performed digitally by using the remote controller or set’s volume and channel change function buttons. Note: There are still a few analog adjustments in the L-series such as 120V adjust, focus, master screen voltage and coils in the picture I/F detector circuit.
  • Page 14 0~63 TEXT BOX 0~127 TEXT PICTURE 0~80 CCD LEVEL 0~10 OPTION 0~63 13VT-N100/150 Must be set to "39" *No adjustment is required due to proper setting being made by IC2001 automatically. Table - B ADJUSTMENT PART NOTE REPLACED NECESSARY UNNECESSARY IC2001 Data is stored in IC2003.

  • Page 15: Service Adjustment

    13VT-N100 13VT-N150 13VT-CN10 Ë SERVICE ADJUSTMENT VCO Adjustment White Balance Adjustment 1. Connect a digital voltmeter between pin (44) of IC401 1. Select a good local channel. and ground. 2. Enter the service modeand select the service 2. Select a good local channel.
  • Page 16 13VT-N100 13VT-N150 13VT-CN10 Vertical-Size Adjustment 1. Select a good local channel. 2. Enter the service mode and select the service adjustment item "V-AMP". 3. While observing the top and bottom of the screen, adjust "V-AMP" data value to proper vertical size and linearity.

  • Page 17: Precautions In Reassembling

    13VT-N100 13VT-N150 13VT-CN10 PRECAUTIONS IN REASSEMBLING MOUTING THE CASSETTE CONTROLLER Initial setting is indispensable before placing the cassette controller in the mechanism. The initial setting is made in two ways;electrical and mechanical. Electrical setting: Make a short-circuit between TP7701 and TP7702 and be sure that the mechanism is back to its initial setting position (*1).

  • Page 18: Function Of Major Mechanical Parts

    13VT-N100 13VT-N150 13VT-CN10 FUNCTION OF MAJOR MECHANICAL PARTS (TOP VIEW) Take-up Pole Base Ass'y Automatic Head Cleaner Ass'y Drum Ass'y Drum Motor A/C Head Ass'y Fixing Guide Pinch Roller Lever Ass'y Full Erase Head Pinch Drive Supply Pole Reverse Guide...

  • Page 19: Bottom View

    13VT-N100 13VT-N150 13VT-CN10 FUNCTION OF MAJOR MECHANICAL PARTS (BOTTOM VIEW) Capstan D. D. Motor Drive Belt Slow Brake Shifter Master Cam Casecon Drive Gear Limiter Pulley Ass'y Clutch Lever Function Function Slow brake Limiter pulley ass’y Gets in contact with the capstan D.D. motor Transmits the power of the capstan D.D.

  • Page 20: Adjustment, Replacement And Assembly Of Mechanical Units

    13VT-N100 13VT-N150 13VT-CN10 ADJUSTMENT, REPLACEMENT AND ASSEMBLY OF MECHANICAL UNITS The explanation given below relates to the on-site general service (field service) but it does not relates to the adjustment and replacement which need high-grade equipment, jigs and skill. For example, the drum assembling, replacement and adjustment service must be performed by the person who have finished the technical courses.
  • Page 21 13VT-N100 13VT-N150 13VT-CN10 Jig ltem Part No. Code Configuration Remarks These tapes are especially used for electrical fine adjustment. Video Audio Hi-Fi Audio Track 10. Alignment Tape 525 Monoscope — 58µm VROATSV NTSC Color Bar — 58µm 46/58 VRONBZGS —...
  • Page 22 13VT-N100 13VT-N150 13VT-CN10 MAINTENANCE CHECK ITEMS AND EXECUTION TIME Perform the maintenance with the regular intervals as follows so as to maintain the quality of machine. Maintained 500 1000 1500 2000 3000 Possible symptom Remarks Parts hrs. hrs. hrs. hrs.
  • Page 23 13VT-N100 13VT-N150 13VT-CN10 REMOVING AND INSTALLING THE CAS- Notes: SETTE HOUSING 1. When fitting the S/E sensor holder to the cassette controller frame L/R, take care. • Removal 2. Misengagement of teeth of casecon drive gear and 1. In the cassette eject mode, remove the cassette.
  • Page 24 13VT-N100 13VT-N150 13VT-CN10 REEL DISK REPLACEMENT AND HEIGHT 4. Assemble the Sup main brake ass'y. CHECK Notes: • Removal 1. When installing the reel disk, take due care so that the 1. Remove the cassette housing control assembly. tension band ass'y is not deformed and grease does 2.
  • Page 25 13VT-N100 13VT-N150 13VT-CN10 Note: Notes: Whenever replacing the reel disk, perform the height 1. Hold the torque gauge by hand so that it is not moved. checking and adjustment. 2. Do not keep the reel disk in lock state. Do not allow long-time measurement.
  • Page 26 13VT-N100 13VT-N150 13VT-CN10 Notes: CHECKING AND ADJUSTMENT OF TAKE- 1. Hold the torque gauge by hand so that it is not moved. UP TORQUE IN VIDEO SEARCH REWIND 2. Do not keep the reel disk in lock state. Do not allow MODE long-time measurement.
  • Page 27 13VT-N100 13VT-N150 13VT-CN10 CHECKING THE VIDEO SEARCH REWIND BACK TENSION • Remove the cassette housing control assembly. • After short-circuiting TP7701 and TP7702 pro- Tension gauge Pinch roller vided at the left on the main PWB, plug in the 900 - 1,200g power cord, then turn on the power.
  • Page 28 13VT-N100 13VT-N150 13VT-CN10 2. Visually check to see if the right edge of the tension Tension pole adjuster adjusting range pole is within the 1.5 ± 0.25mm from the right edge of the Sup guide shaft. Tension pole adjuster Sup guide shaft Tension pole 1.5 ±...
  • Page 29 13VT-N100 13VT-N150 13VT-CN10 • Adjustment • Checking the brake torque at the take-up side 1. If the indication of torque cassette meter is lower than the setting, shift the tension spring engagement to the part A. Torque gauge 2. If the indication of torque cassette meter is higher than the setting, shift the tension spring engagement to the part B.
  • Page 30 13VT-N100 13VT-N150 13VT-CN10 3. Align the left end of gear of A/C head arm with the REPLACEMENT OF A/C (Audio/Control) HEAD punched mark of chassis, tentatively tighten the screws 1. Remove the cassette housing control assembly. 1 and 2 so as to ensure smooth motion of A/C head 2.
  • Page 31 13VT-N100 13VT-N150 13VT-CN10 A/C HEAD HEIGHT ROUGH ADJUSTMENT HEIGHT ADJUSTMENT OF REVERSE GUIDE • Setting 1. Adjust the height from the mechanism chassis to the reverse guide lower flange to 13.38mm, using the Azimuth screw reverse guide height adjustment jig, in tape loading state.
  • Page 32 13VT-N100 13VT-N150 13VT-CN10 Notes: ADJUSTMENT OF TAPE DRIVE TRAIN 1. Previously set the tracking control in the center posi- 1. Tape run rough adjustment tion, and adjust the envelope waveform to maximum 1 Remove the cassette housing control assembly. with X value adjustment nut. Thereby the tape run 2 After shortcircuiting TP7701 and TP7702 provided rough adjustment is facilitated.
  • Page 33 13VT-N100 13VT-N150 13VT-CN10 3. Tape run adjustment PB CHROMA 1 Connect the oscilloscope to PB CHROMA envelope Envelope output test point, set oscilloscope sync to EXT, trigger-input the PB CHROMA signal (head switch- ing pulse). 2 Rough adjustment of X value...
  • Page 34 13VT-N100 13VT-N150 13VT-CN10 REPLACEMENT OF DRUM D.D. MOTOR REPLACEMENT OF THE CAPSTAN D.D. 1. Set the eject mode. (DIRECT DRIVE) MOTOR 2. Withdraw the main power plug from the socket. • Remove the mechanism from the main PWB (refer to Page10 "DISASSEMBLY AND REASSEMBLY"...
  • Page 35 13VT-N100 13VT-N150 13VT-CN10 REPLACING THE UPPER AND LOWER DRUM ASSEMBLING OF PHASE MATCHING ASSEMBLY MECHANISM COMPONENTS • Assemble the phase matching mechanism com- • Replacement (Perform in the numerical order) ponents in the following order. 1 Remove the motor as stated in Page 34 D.D. motor 1.
  • Page 36 13VT-N100 13VT-N150 13VT-CN10 1Insert Reverse Guide Lever Ass’y Insert reverse guide lever ass'y 2 Insert pinch drive cam Align here. Turn the reverse guide lever assembly counterclockwise Fit the pinch drive cam so that the notch of pinch to the stopper.
  • Page 37 13VT-N100 13VT-N150 13VT-CN10 1. Make sure that the loading gear is at the point 1 as INSTALLING THE SHIFTER shown below. 2. Install, paying attention to 6 insertion points and 3 release points. Drum 3. For the phase matching at the insertion point 1, see Capstan the point 2 as shown below.
  • Page 38 13VT-N100 13VT-N150 13VT-CN10 INSTALLING THE MASTER CAM (AT REAR REPLACEMENT OF LOADING MOTOR • Removal SIDE OF MECHANISM CHASSIS) 1. Make sure beforehand that the shifter is at the point as shown below. 2. Place the master cam in the position as shown below.
  • Page 39 13VT-N100 13VT-N150 13VT-CN10 ASSEMBLY OF CASSETTE HOUSING 1. Drive Gear and R Drive angle ass’y MSPRT0381AJFJ Apply grease Apply grease Apply grease Figure 1-47. 2. Synchro Gear, Drive Gear L and Drive Gear R LANGF9592AJFW Top surface should be free from scratches or soil.

  • Page 40: Adjustment Of The Vcr Electrical Circuitry

    13VT-N100 13VT-N150 13VT-CN10 ADJUSTMENT OF THE VCR ELECTRICAL CIRCUITRY Notes: » Before the adjustment: Electrical adjustments described here are often required after replacement of electronic components and mechanical parts such as video heads. Check that the mechanism and all electric components are in good working condition prior to the adjustments, otherwise adjustments can not be completed.
  • Page 41 13VT-N100 13VT-N150 13VT-CN10 Ë Test points layout of Main Unit. Figure 2-2. ADJUSTMENT OF STILL PICTURE VERTICAL SYNC 1. Play back the EP Self-recorded tape in the still mode. Measuring Monitor screen 2. Using the CH '/" (TR ± —...

  • Page 42: Troubleshooting

    13VT-N100 13VT-N150 13VT-CN10 TROUBLESHOOTING OF VCR SECTION...
  • Page 43 13VT-N100 13VT-N150 13VT-CN10...
  • Page 44 13VT-N100 13VT-N150 13VT-CN10...
  • Page 45 13VT-N100 13VT-N150 13VT-CN10...
  • Page 46 13VT-N100 13VT-N150 13VT-CN10...
  • Page 47 13VT-N100 13VT-N150 13VT-CN10...
  • Page 48 13VT-N100 13VT-N150 13VT-CN10...
  • Page 49 13VT-N100 13VT-N150 13VT-CN10...
  • Page 50 13VT-N100 13VT-N150 13VT-CN10...
  • Page 51 13VT-N100 13VT-N150 13VT-CN10 TROUBLESHOOTING OF TV SECTION...
  • Page 52 13VT-N100 13VT-N150 13VT-CN10...
  • Page 53 13VT-N100 13VT-N150 13VT-CN10...

  • Page 54: Chassis Layout

    13VT-N100 13VT-N150 13VT-CN10 CHASSIS LAYOUT PWB-B PWB-D PWB-C PWB-A...

  • Page 55: Block Diagram Of Tv Section

    13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF TV SECTION...

  • Page 56: Block Diagram Of Vcr Section

    13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF VCR SECTION Ë OVERALL BLOCK DIAGRAM...
  • Page 57 13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF VCR SECTION Ë SERVO PROCESS BLOCK DIAGRAM...
  • Page 58 13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF VCR SECTION Ë SYSTEM CONTROL BLOCK DIAGRAM Ë SAFETY DEVICE BLOCK DIAGRAM...
  • Page 59 13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF VCR SECTION Ë VIDEO SIGNAL FLOW BLOCK DIAGRAM...
  • Page 60 13VT-N100 13VT-N150 13VT-CN10 BLOCK DIAGRAM OF VCR SECTION Ë AUDIO BLOCK DIAGRAM...

  • Page 61: Overall Schematic Diagram

    13VT-N100 13VT-N150 13VT-CN10 OVERALL SCHEMATIC DIAGRAM...

  • Page 62: Description Of Schematic Diagram

    13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : CRT Unit DESCRIPTION OF SECTION SCHEMATIC DIAGRAM NOTES: WAVEFORM MEASUREMENT CONDI- 1. The unit of resistance "ohm" is omitted TIONS: (K=1000 ohms, M =1 Meg ohm). 1. Photographs taken on a standard gated color bar 2.
  • Page 63 13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : MAIN-1 Unit (TV Section)
  • Page 64 13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : MAIN-2 Unit (TV Section)
  • Page 65 13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : FRONT AV and POWER Unit (TV Section)
  • Page 66 13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : MAIN-3 Unit (VCR Section)
  • Page 67 13VT-N100 13VT-N150 13VT-CN10 SCHEMATIC DIAGRAM : MAIN-4 Unit (VCR Section)

  • Page 68: Printed Wiring Board Assemblies

    13VT-N100 13VT-N150 13VT-CN10 PRINTED WIRING BOARD ASSEMBLIES PWB-B: CRT Unit (Wiring Side) PWB-D: FRONT AV Unit (Wiring Side)
  • Page 69 13VT-N100 13VT-N150 13VT-CN10 PWB-C: POWER Unit (Wiring Side)
  • Page 70 13VT-N100 13VT-N150 13VT-CN10 PWB-A: MAIN Unit (Wiring Side)
  • Page 71 13VT-N100 13VT-N150 13VT-CN10 PWB-A: MAIN Unit (Chip Parts Side)

  • Page 72: Replacement Parts List

    2. NO. DE REF 3. NO. DE PIECE 4. DESCRIPTION in USA: Contact your nearest SHARP Parts Distributor to order. For in CANADA: Contact SHARP Electronics of Canada Limited location of SHARP Parts Distributor, Please call Toll-Free; Phone (416) 890-2100...

  • Page 73: Main Unit

    13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code D402 RH-EX0603GEZZ J Zener Diode, 3.8V PWB-A: DUNTKA037FMV0 D451 RH-EX0616GEZZ J Zener Diode, 5.6V MAIN Unit D455 RH-DX0475CEZZ J Diode D501 RH-DX0441CEZZ J Diode TUNER å...
  • Page 74 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C414 VCE9GA1HW105M J 1 EL. (N.P) PWB-A: DUNTKA037FMV0 C418 VCKYCY1HF103Z J 0.01 Ceramic MAIN Unit (Continued) C419 VCEA0A1CW476M J 47 C420 VCE9GA1HW105M J 1 EL. (N.P)
  • Page 75 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C6613 VCEAKA0JW476M J 47 6.3V PWB-A: DUNTKA037FMV0 C6614 VCEAKM1CW226MJ 22 MAIN Unit (Continued) C6615 VCEA9A0JW476M J 47 6.3V C6616 VCKYCY1CB104K J 0.1 Ceramic C2210 VCKYCY1HF103Z J 0.01 Ceramic C6617 VCKYCY1CB104K J 0.1...
  • Page 76 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R429 VRD-RA2EE101J J 100 1/4W Carbon PWB-A: DUNTKA037FMV0 R433 VRN-MD2AL000J J 0 1/10W M-Film MAIN Unit (Continued) R434 VRN-MD2AL102J J 1k 1/10W M-Film R435 VRN-MD2AL102J J 1k...
  • Page 77 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R2294 VRN-MD2AL000J J 0 1/10W M-Film PWB-A: DUNTKA037FMV0 R3178 VRN-MD2AL221J J 220 1/10W M-Film MAIN Unit (Continued) R3179 VRN-MD2AL221J J 220 1/10W M-Film R3180 VRN-MD2AL221J J 220 1/10W M-Film R2026 VRN-MD2AL562J J 5.6k 1/10W M-Film...
  • Page 78 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code S2510 QSW-K0077GEZZ J Vol-Down PWB-A: DUNTKA037FMV0 MAIN Unit (Continued) MISCELLANEOUS PARTS å F701 QFS-B4023CEZZ J Fuse 4A R7737 VRN-MD2AL102J J 1k 1/10W M-Film R7738 VRN-MD2AL562J J 5.6k 1/10W M-Film QFS-A4021GEZZ R7739 VRN-MD2AL562J J 5.6k 1/10W M-Film...

  • Page 79: Crt Unit

    13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-B: DUNTKA039WEV0 PWB-C: DUNTKA038WEV0 CRT Unit POWER Unit TRANSISTORS INTEGRATED CIRCUIT Q853 VS2SC2229O/1E J 2SC2229O å IC701 VHiSTRG6624-1 J STRG6624 Q854 VS2SC2229O/1E J 2SC2229O å...
  • Page 80 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-C: DUNTKA038WEV0 RESISTORS [M-Ox.··· Metal Oxide, M-Film··· Metal Film] POWER Unit (Continued) R440 VRD-RA2BE750J J 75 1/8W Carbon å R701 VRW-KP3HC1R8K J 1.8 Cement COILS å...
  • Page 81 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PWB-C: DUNTKA038WEV0 POWER Unit (Continued) P701 QPLGN0207CEZZ J Plug, 2-Pin (M) P702 QPLGN0304CEZZ J Plug, 3-Pin (E) P705 QPLGN0361CEZZ J Plug, 3-Pin (OC) P707 QPLGN0361CEZZ J Plug, 3-Pin (PG)
  • Page 82 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code MSPRC0223AJFJ V Azimuth Spring MECHANISM CHASSIS MSPRC0224AJFJ V Height Adjusting spring LBNDK1011AJZZ V Tension Band Ass’y LBOSZ1007AJZZ V Tension Arm boss SCREW, NUTS AND WASHERS LBOSZ1006AJZZ V Cassette Stay L LCHSM0166AJZZ V Main Chassis Ass’y...
  • Page 83 13VT-N100 13VT-N150 13VT-CN10 MECHANISM CHASSIS PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...
  • Page 84 13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CASSETTE HOUSING CONTROL CHLDX3081TEV2 V Cassette Housing LANGF9592AJFW V Upper Plate LHLDX1028AJ00 V Frame (L) LHLDX1032AJ00 V Frame (R) LHLDX1030AJZZ V Holder (L) LHLDX1031AJZZ V Holder (R)
  • Page 85 13VT-N100 13VT-N150 13VT-CN10 CASSETTE HOUSING CONTROL PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...
  • Page 86 1-15 QCNW-2206PEZZ R Connecting Wire 1-16 VSP9050PB15WA J Speaker, x1 1-17 LX-TZ0012PEFD R Screw, x4 GCABB2349PEKA R Rear Cabinet (13VT-N100) BB GCABB2349PEKB R Rear Cabinet (13VT-N150) BB GCABB2351PEKA R Rear Cabinet (13VT-CN10) BB QACCD3064CESA J AC Cord å (13VT-N100/CN10) å...
  • Page 87 13VT-N100 13VT-N150 13VT-CN10 CABINET AND MECHANICAL PARTS Ref. No. Part No. Description Code Ref. No. Part No. Description Code...

  • Page 88: Packing Parts

    Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESORIES (NOT REPLACEMENT ITEM) TGAN-0018PEZZ Guarantee Card SPAKC6405PEZZ – Packing Case (13VT-N100) — (13VT-N100/150) SPAKC6406PEZZ – Packing Case (13VT-N150) — TCAUH0011PEZZ Caution Card SPAKC6426PEZZ – Packing Case (13VT-CN10) — (13VT-N100/150) SSAKA0031PEZZ –...

  • Page 89: Packing Of The Set

    13VT-N100 13VT-N150 13VT-CN10 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET • SETTING POSITIONS OF THE KNOBS Power SW Polyethyrene Bag Operation Manual Guarantee Card Batteries Infrared R/C Unit Polyethylene Sack Buffer Material...
  • Page 90 Code Ref. No. Part No. Description Code COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

13vt-n15013vt-cn10

Table of Contents