U-V VISIBLE SPECTROSCOPY

-
 U-V VISIBLE SPECTROSCOPY 
  • UV-Vis spectrum results from the interaction of EM radiation in the UV-Vis region with atoms and molecules.
  • The UV radiation region extends from 200nm to 400nm and the visible region extends from 500nm to 800nm.
  • Organic compounds, inorganic compounds, and coordination compounds fall in the UV-Vis spectrum.
THEORY
  • The absorption of radiation in the UV-Vis region of the spectrum is dependent on the electronic structure of the absorbing species. 
  • When a photon of a given wavelength interacts with a molecule it may cause a transition among the electronic energy levels if its energy matches with the difference in the energies of these levels.
  • A given electronic energy level has a number of vibrational energy levels in it and each of the vibrational energy levels has a number of rotational energy levels in it. So along with the electronic transition, vibrational and rotational transitions also occur simultaneously. So electronic spectrum appears broad.
  • Transitions involving π orbitals and lone pairs are identified using UV-Vis spectrometers.
INSTRUMENTATION 

  


The sample is irradiated with UV-Vis radiation from a source. Monochromatic radiation is employed at a time. The amount of radiation absorbed at each wavelength is measured.
Spectrum is the plot of wavelength or frequency versus intensity of absorption. 
Light absorbed is directly proportional to the concentration in the sample.
Location: United States

Comments

Post a Comment

Popular posts from this blog

GLASS ELECTRODE

-
Image
 GLASS ELECTRODE It is a secondary reference electrode that produces a constant and reproducible electrode potential. It is an ion-selective electrode used with other reference electrodes to generate a potential difference. Construction It is made up of a special glass of relatively low melting point and high electrical conductivity, in the form of a sealed glass tube filled with 0.1M HCl, a platinum wire is inserted into it, to make electrical contact. The glass electrode is represented as Pt| 0.1M HCl | Glass | H+    The H+ ion concentration inside the electrode is constant. When the electrode is immersed into a solution of unknown H+, it becomes sensitive to the outside concentration in the solution. Such a sensitivity arises because of the difference between the H+ ion concentration inside and outside.       The electrode potential of the glass rod is : EG = EG0 + 0.0591 log [ H+ ]     EG = EG0 - 0.0591 pH  The glass electrode i...
Read more

CHROMATOGRAPHY

-
Image
CHROMATOGRAPHY  It is a method used for the separation, purification, and identification of a mixture of substances. It is useful when components of a mixture have similar physical and chemical properties and hence cannot be separated by other methods. Principle: It is based on the distribution of the components in a mixture between a stationary and a mobile phase. The stationary phase may be a column of adsorbent, a paper, a thin layer of adsorbent through which the mobile phase moves on. The mobile phase may be a liquid or gas. The principle of chromatographic separation is always adsorption (absorption of a constituent on the surface of the solid stationary phase) or partition (distribution of a constituent in between two liquid stationary phases). THEORY OF CHROMATOGRAPHY The separation takes place due to the differential migration of components which depends on the relative affinity towards the stationary and mobile phases.  The component which is less strongly held by th...
Read more

THIN LAYER CHROMATOGRAPHY

-
Image
 THIN LAYER CHROMATOGRAPHY It is a chromatographic separation method used to separate mixtures, to check the purity of a mixture, and to monitor the progress of the reaction. Procedure A glass plate coated with a material of the adsorbent will constitute the stationary phase. The material is made into a slurry or a paste and the glass plate is coated with it by a thin layer applicator and dried. This glass plate with a thin layer of stationary phase is called chromatoplate. The mixture to be separated is applied to one end of the plate and it is placed in the solvent. When the solvent reaches near the top, it is removed and dried. If the components are colored the spots can be readily located. If the components are colorless the dried plate is sprayed with a suitable reagent to make the spot colored. In this way, the position of the components is located and their Rf values are determined. Rf value is the ratio of the distance traveled by a component to the distance traveled by the...
Read more