anisole

Anisole, CAS # 100-66-3
Standard Operating Procedure
Anisole
This is an SOP template and is not complete until: 1) lab specific information is entered into the box
below 2) lab specific protocol/procedure is added to the protocol/procedure section and
3) SOP has been signed and dated by the PI and relevant lab personnel.
Print a copy and insert into your
Laboratory Safety Manual and Chemical Hygiene Plan.
Refer to instructions for assistance.
School / Department:
Click here to enter text.
SOP Preparation Date:
Click here to enter a date.
Principal Investigator:
Click here to enter text.
Lab Manager Name:
Click here to enter text.
Laboratory Phone:
Click here to enter text.
Office Phone:
Click here to enter text.
Emergency Contact:
Click here to enter text.
Contact Phone:
Click here to enter text.
SOP Approval Date:
Click here to enter a date.
Laboratory locations covered by this SOP (building / room number):
Click here to enter text.
Type of SOP:
☐
Process
☒
Hazardous Chemical
☐
Hazardous Class
Purpose
Anisole is a solvent used in the synthesis of organic compounds and in large-scale applications such as the
production of perfume.
Physical and Chemical Properties / Definition of Chemical Group
CAS:
Class:
Molecular Formula:
Form (physical state):
Color:
Boiling Point:
100-66-3
Combustible, Flammable, Acute toxin, Irritant
C7H8O
Liquid
Colorless
154 oC
ASU Department of Environmental Health & Safety
Page | 1
Anisole, CAS # 100-66-3
Potential Hazards / Toxicity
Potential Health Effects
Target Organs:
Inhalation:
Skin:
Eyes:
Ingestion:
N/A
May be harmful if inhaled. May cause respiratory tract irritation.
May be harmful if absorbed through skin. May cause skin irritation.
May cause eye irritation.
May be harmful if swallowed.
Personal Protective Equipment (PPE)
Respiratory Protection
Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator
with multi-purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup
to engineering controls. If the respirator is the sole means of protection, use a full-face supplied
air respirator. Use respirators and components tested and approved under appropriate
government standards such as NIOSH (US) or CEN (EU).
Respirators should be used only under any of the following circumstances:
 As a last line of defense (i.e., after engineering and administrative controls have been
exhausted).
 When Permissible Exposure Limit (PEL) has exceeded or when there is a possibility that PEL will
be exceeded.
 Regulations require the use of a respirator.
 An employer requires the use of a respirator.
 There is potential for harmful exposure due to an atmospheric contaminant (in the absence of
PEL)
 As PPE in the event of a chemical spill clean-up process
Lab personnel intending to use/wear a respirator mask must be trained and fit-tested by EH&S.
This is a regulatory requirement.
(http://www.asu.edu/uagc/EHS/documents/asu_respriatory_protection_plan.pdf)
Hand Protection
Handle with gloves. Use proper glove removal technique to avoid skin contact with this product.
Nitrile gloves are recommended.
NOTE: Consult with your preferred glove manufacturer to ensure that the gloves you plan on
using are compatible with anisole.
ASU Department of Environmental Health & Safety
Page | 2
Anisole, CAS # 100-66-3
Refer to glove selection chart from the links below:
http://www.ansellpro.com/download/Ansell_8thEditionChemicalResistanceGuide.pdf
OR
http://www.allsafetyproducts.biz/page/74172
OR
http://www.showabestglove.com/site/default.aspx
OR
http://www.mapaglove.com/
Eye Protection
 Wear chemical splash goggles and a face shield to protect from splash hazards and chemical
vapors.
Skin & Body Protection
 Fire/flame resistant lab coat, preferably made from antistatic material.
 Full-length pants
 Closed-toe rubber or leather shoes
Hygiene Measures
Avoid contact with skin, eyes, and clothing. Wash hands before breaks and immediately after
handling the product.
Engineering Controls
Use process enclosure, local exhaust ventilation, or other engineering controls to control airborne
levels below recommended exposure limits.
First Aid Procedures
If inhaled… Move to fresh air. If the person is not breathing, give artificial respiration. Avoid
mouth to mouth contact. If breathing is difficult, give oxygen. Seek immediate medical attention.
Call 911 from a campus phone or (480) 965-3456. Call EH&S at (480) 965-1823.
In case of skin contact… Remove all contaminated clothing. Immediately (within seconds)
flush affected area for FIFTEEN (15) minutes. Seek immediate medical attention. Call 911 from a
campus phone or (480) 965-3456 from a cell phone. Call EH&S at (480) 965-1823.
In case of eye contact… Remove any contact lenses. Use nearest emergency eyewash
immediately for at least FIFTEEN (15) minutes. Seek immediate medical attention. Call 911 from
a campus phone or (480) 965-3456 from a cell phone. Call EH&S at (480) 965-1823.
ASU Department of Environmental Health & Safety
Page | 3
Anisole, CAS # 100-66-3
If swallowed… DO NOT INDUCE VOMITING. Never give anything by mouth to an unconscious
person. Give 2-4 cupfuls of milk or water. Seek immediate medical attention. Call 911 from a
campus phone or (480) 965-3456 from a cell phone. Call EH&S at (480) 965-1823.
Special Storage & Handling Requirements
Storage






Ensure the container is tightly closed at all times.
Keep in a cool, dry, well-ventilated area away from incompatible materials and conditions.
Containers which are opened must be carefully resealed and kept upright to prevent
leakage.
Keep away from heat, flames, and other sources of ignition.
Store in a designated flammables area.
Store protected from moisture.
Handling












The lab where the material is being handled has an approved / certified emergency eyewash
and safety shower.
Ensure you are wearing the following minimum PPE: tightly fitting safety goggles and face
shield, fire/flame resistant lab coat, full length pants, close-toe rubber or leather shoes,
nitrile gloves.
Lab emergency contact information must be readily posted. Easy access to a cellular phone
or land line is readily available.
Avoid inhalation of vapor or mist.
Avoid contact with skin, eyes, or clothing.
Keep away from heat, flames, and other sources of ignition.
Take measures to prevent the buildup of electrostatic charge.
Ground and bond containers when transferring material.
Use spark-proof tools and explosion proof equipment.
Empty containers retain product residue (liquid and/or vapor), and can be dangerous- always
tightly reseal empty containers
Do not allow product to come in contact with water.
Do not pressurize, cut, weld, braze, solder, drill, or grind on or near empty containers.
Spill and Accident Procedure
Personal precautions
Avoid breathing vapors, mist or gas. Ensure adequate ventilation. Remove all sources of
ignition. Evacuate personnel to safe areas. Do not attempt clean-up without minimum PPE.
Beware of vapors accumulating to form explosive concentrations. Vapors can accumulate in low
areas.
ASU Department of Environmental Health & Safety
Page | 4
Anisole, CAS # 100-66-3
Environmental precautions
Prevent further leakage or spillage – if safe to do so. Do not allow product to enter drains.
Methods and materials for containment and clean-up
Consider material compatibility prior to clean-up. Verify spill kit is available. Absorb spill with
inert material, and place in suitable container.
1. Immediately assess amount spilled, follow posted ASU Emergency Response Guide
procedures for hazardous materials incidents.
2. If a chemical exposure has occurred, a fellow lab worker shall call 9-1-1 and EH&S at (480)
965-1823.
3. Don compatible gloves and other protective PPE if not already being worn.
4. Secure / restrict access to the area of the spill to prevent spread of the chemical.
5. Use the available spill kit to stop and contain the spill. Bag the collected material.
6. Label and tag as hazardous waste and submit a pick-up request to EH&S using EHS Assistant.
Decontamination / Waste Disposal Procedure
Label waste

Attach a completed ASU Hazardous Waste tag to all waste containers as soon as the first
drop of waste is added to the container.
Store waste



Store hazardous waste in closed containers, in secondary containment and in a designated
storage location.
Double-bag dry waste using sealable transparent bags.
Waste must be under the control of the person generating and disposing of it.
Dispose of waste



Dispose of regularly generated chemical waste within 90 days.
Use EHS Assistant online hazardous waste pick-up request system.
Contact ASU EH&S at (480) 965-1823 with questions.
Protocol / Procedure
Laboratory-specific procedures
Add your lab’s specific procedures in this section.
Click here to enter text.
IMPORTANT NOTE: Any deviation from this SOP requires advance PI approval.
Documentation of Training

Prior to conducting any work with this material, Principal Investigator or designee must
provide to his/her laboratory personnel specific to the hazards involved in working with this
substance, work area decontamination, and emergency procedures.
ASU Department of Environmental Health & Safety
Page | 5
Anisole, CAS # 100-66-3


The Principal Investigator must provide his/her laboratory personnel with a copy of this SOP
and a copy of the MSDS provided by the manufacturer.
The Principal Investigator must ensure that his/her laboratory personnel have attended
appropriate/required laboratory safety training or refresher training within the last one year.
I have read and understand the content of this SOP.
Employee Name
ASU Affiliate No.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
Click here to enter text.
ASU Department of Environmental Health & Safety
Signature
Date
Click here to enter a date.
Click here to enter a date.
Click here to enter a date.
Click here to enter a date.
Click here to enter a date.
Click here to enter a date.
Click here to enter a date.
Page | 6