FAAC 787456 Ezi ntụziaka dịpụrụ adịpụ

FAAC 787456 Genuine Remote

Ozi ngwaahịa

The FAAC Remote is a wireless device used for controlling a radio receiver. It allows users to remotely operate a device or system that is connected to the receiver. The remote uses coded signals to ensure secure and reliable communication with the receiver

Ntuziaka ojiji ngwaahịa

Coding via Master Remote:

1. Place one master remote that has already been coded and the new remote head to head on a flat surface, like a table.
2. Simultaneously press buttons P1 and P2 on the already coded remote. Release the buttons when the light on the remote flashes.
3. Hold down one of the buttons on the already-coded remote.
4. Hold down the same button on the new remote. Wait until the light on the new remote flashes twice and then goes out, indicating that the operation has been successful.
5. Release all the buttons.
6. Verify that the new remote is working properly.

Making a New Master:

Rịba ama: Coding a new remote as a master will delete all other remotes previously programmed for your device. The remaining remotes can be programmed as slaves to the new master.

1. Open the box containing the radio receiver.
2. Simultaneously press buttons P1 and P2 on a remote that has already been coded. Release them when the light on the remote flashes.
3. On the receiver card, hold down the learning button (round button SW1) until the light on the card flashes.
4. While holding down the learning button, hold down one of the buttons on the remote until the light on the card stays on for 2 seconds.
5. Release all the buttons.
6. Verify that the new remote is working properly.
7. Close the box containing the radio receiver.

Maka ozi ndị ọzọ na nkwado, gaa na www.remotepro.com.au.

FAAC Remote Coding

Biko rụba ama: During programming, don’t press the keys on the new remote first, you risk deleting the old remote. – During coding the device will be activated. In this range of remotes, there are
“master” remotes and “slave” remotes. “Master” remotes can share their code with other remotes and learn from other “master” remotes. “Slave” remotes cannot share their codes with another remote. To determine the type of your remote, hold down a button: – if the light flashes once then remains lit, it is a “master” remote – if the light comes on continuously without flashing, it is a “slave” remote

CODING VIA MASTER REMOTE

1. On a flat surface, like a table, place one “master” remote that has already been coded and your new remote head-to-head.
2. At the same time, press buttons P1 and P2 on the remote that has already been coded. Release the buttons when the light on the remote flashes.
3. Next, hold down one of the buttons on the remote that has already been coded.
4. Hold down the same button on the new remote. Wait until the light on your new remote flashes twice and then goes out, indica?ng that the opera?on has been successful.
5. Release all the buttons.
6. Verify that your new remote is working.

MAKING A NEW MASTER

Coding the new remote will delete all other remotes previously programmed for your device. Once a new master has been made you can make slaves of the remaining remotes

1. Open the box containing the radio receiver.
2. At the same time, press buttons P1 and P2 on a remote that has already been coded. Release them when the light on the remote flashes.
3. On the receiver card, hold down the learning button (round button SW1) until the light on the card flashes.
4. Holding down the learning button, hold down one of the buttons on the remote until the light on the card stays on for 2 seconds.
5. Release all the buttons.
6. Verify that your new remote is working.
7. Close the box containing the radio receiver.

www.remotepro.com.au

Ịdọ aka ná ntị

• Iji gbochie ajọ mmerụ ahụ ma ọ bụ ọnwụ nwere ike:
  • Batrị dị ize ndụ: ekwela ka ụmụaka nọrọ nso na batrị.
  • Ọ bụrụ na eloro batrị, gwa dọkịta ozugbo.
• Iji belata ihe egwu nke ọkụ, mgbawa ma ọ bụ ọkụ kemịkal:
  • Dochie naanị otu nha na ụdị batrị ahụ
  • AKWỤKWỌ, KWASỊTA, ikpo ọkụ karịrị 100C ma ọ bụ batrị na-ere ọkụ ga-ebute mmerụ ahụ dị ukwuu ma ọ bụ FATAL n'ime awa 2 ma ọ bụ ihe na-erughị ya ma ọ bụrụ na iloro ma ọ bụ tinye ya n'ime akụkụ ahụ ọ bụla.

Akwụkwọ / akụrụngwa

FAAC 787456 Genuine Remote [pdf] Ntuziaka 787456, Genuine Remote

Ntụaka

• Ebe ndọba ụgbọala, akpaaka & Ọnụ ụzọ | Ụgbọ ala | Mbupu efu – Pro Remote
• Akwụkwọ ntuziaka onye ọrụ