Cell2 OF01 Otu akwụkwọ ntuziaka onye ọrụ ọkụ ọkụ
WIRING
Ọrụ
Maka Nhọrọ Ụdị Flash:
While activating a warning mode, momentarily apply ODO waya ka + VDC:
- Ozugbo na-esote ụkpụrụ.
- Quick three times to the default flash pattern.
| FP# | Ụkpụrụ Flash |
| 1 | Ugboro abụọ [R65]* |
| 2 | Otu [2Hz] |
| 3 | Ugboro atọ [2Hz] |
| 4 | Quad [2Hz] |
| 5 | Random |
| 6 | EF kwụ ọtọ** |
| 7 | Otu-Quad |
| 8 | Otu H/L |
| 9 | Otu-atọ-Quint |
* Actual approval will be based on the model ordered.
** For use with external flash controller.
Maka mmekọrịta n'otu oge ma ọ bụ nke ọzọ:
- Tinye + VDC to RED and ODO wires simultaneously then remove ODO wire to enter Ụdị nhazi; the lighthead will display short flashes:
- Otu flash = Otu 1
- Ugboro abụọ flash = Otu 2
- To change Group, momentarily apply ODO waya ka + VDC.
- Lightheads nke otu Otu ga-agbanye ọnụ.
- Ìhè nke otu dị iche iche ga-atụgharị ọzọ.
Mara: To comply with ECE R65, 4 units need to be synchronised and set to the same group.
- Chekwa ma pụọ Ụdị nhazi site n'ịkwụsị ike niile.
Function Wire Setting – OFF Override or Cruise Mode:
- Tinye + VDC ka Uhie , Ọcha na ODO wires simultaneously then remove just the ODO wire to enter FUNCTION WIRE SETTING; the lighthead will display short flashes:
- Triple flash = OFF Override (default)
- Quad flash = Cruise Mode
- To change Function, momentarily apply ODO waya ka + VDC.
- Chekwa ma pụọ FUNCTION WIRE SETTING site n'ịkwụsị ike niile.
Tọgharịa na ntọala ụlọ nrụpụta:
- Tinye + VDC ka Uhie na ODO wires simultaneously then remove ODO wire to enter Ụdị nhazi.
- Tinye na + VDC for more than 5 seconds. The lighthead will display fast short flashes to signify restoring successfully.
- Chekwa ma pụọ Ụdị nhazi site n'ịkwụsị ike niile.
Ịwụnye
(Covert Mount for Side Mirror with Turn Signal Light)
Mkpa:
The disassembling method of the original vehicle parts will be different based on each vehicle manufacturer and model, please refer to original vehicle manufacturer’s manual before installation.
- Remove the front mirror using a plastic pry tool.
- Remove the side mirror cover by pushing the clips or loose screws from inside to access the harness assembly.
- Disconnect the wire harness and disassemble the turn signal light assembly from the side mirror unit.
- Drill an 8.5mm hole with 4mm depth on the inner lens or reflector of the turn signal light assembly.
- Apply silicone and fix the lighthead into the assembly. 3. Assemble the turn signal light back into side mirror set.
- Route lighthead’s wire into vehicle chassis and connect the wires to the switch accordingly.
Mara: Ensure the mark is oriented upward for correct optical distribution.
Test the lighthead before reassembling the side mirror cover and mirror back.
APPROVED MOUNTING POSITION
The lightheads must be set up in a set of four units to meet ECE R65 Cat. X. (Amber, Blue, Red)
Follow the diagram and position the lightheads within the maximum separation distance to fulfill the approval requirement.
Ngwa Examples
Akwụkwọ / akụrụngwa
| Cell2 OF01 Otu ọkụ ọkụ ọkụ [pdf] Akwụkwọ ntuziaka onye ọrụ OF01 Single LED Lighthead, OF01, Single LED Lighthead, LED Lighthead, Lighthead |