SPECIFICATIONS
STANDARD FEATURES
- Inside height and rear door opening height of 110″
- Sealedwiring harnesswith internal ground
- Hot-dip galvanized steel rear frame and rear underride guard
- Easy operating door lock rodswith rubber handle grips for operatorcomfort and safety
- Water and debris resistant tail light housing
- Computer controlled machine riveting of sides and roof
GENERAL
Customizable linings from composite to plywood,
along with insulated heaters for your hauling needs.
| Length | Exterior: 53′ 0″ Interior: 52′ 6″ |
| Width | Exterior: 102.36″ Interior: 99″ lining to lining |
| Height | Exterior: 13′ 6″ Interior: 110 |
| Capacity | 68,000 GVWR 3970 cu. ft. of interior volume |
| Tare Weight | 13,900 lbs |
BODY CONSTRUCTION
| Side Sheets | Side sheets .050″ thick pre-painted white aluminum. |
| Side Posts | Galvanized steel posts on 24″ centers, 1-1/8″ deep × 5″ wide, with posts on 12″ centers over coupler and landing gear area. |
| Roof | One piece, 0.040″ thick, full width aluminum sheet, tension leveled prior to installation. |
| Roof Bows | Galvanized steel anti-snag hat section on 24″ centers. Pre-bonded to roof sheet. Roof bows installed using four solid rivets, two per end. |
| Front Wall | Four hi-tensile, hat shaped, posts securely fastened with 6 heavy-duty fasteners and reinforced with a special angle clip, welded to the upper coupler and covered with 0.050 aluminum front sheets. |
| Rear Frame | Hot-dip galvanized, hi-tensile steel construction 3/16″ thick with low profile header, tube shaped posts. Forged steel angle irons in top corners for added rack resistance. Lights recessed in rear sill with heavy-duty protection bars with welded reinforcing bar between tail lamps. |
| Rear Doors | Composite swing door, 0.50″ composite panel. Dual durometer seals bonded to door. Four hinges and one anti-rack locking bar with nylon bushings per door. Lock handles fitted with rubber grips for operator comfort and safety. |
| Interior Lining | Exterior grade plywood, 1/4″ thick, installed horizontally over side posts. Exterior grade 1/2″ plywood installed lower half of front wall and 1/4″ over top height of frontwall. |
UNDERFRAME
| Crossmembers | Four inch deep, hot rolled steel I-beam, 80,000 psi yield strength, located on 12″ centers. Hat shaped crossmembers ahead of landing gear. Rear 4′ of trailer has crossmembers located on 8″ centers |
| Upper Coupler Floor | A.A.R. rated king pin, 3-3/8″ deep. Laminated Oak 1-3/8″ nominal thickness with three screws per floorboard with a 1/8″ steel diamond plate × 12″ deep. |
| Landing Gear | Hot-dipped galvanizedwing plate and support gear bracing mounted to five crossmembers. Two speed, 50,000 lb. capacity, A.A.R. rated, with 10″×10″ sandshoes. Roadside crank handle. |
| Rear Underride Guard | Constructed per CMVSS 223 Regulations. Hot-dip galvanized underrid guard. Bolt-on type with special 4″ square Guard tube with recess for conspicuity tape with end caps for operator safety |
SUSPENSION
| Suspension | Hendrickson Vantraxx HKANT40K Air Ride |
| Hub & Drums | Ten stud, hub piloted with outboard mounted brake drums |
| Wheels | Pre-painted white 8.25 × 22.5 steel disc. |
| Tires | Lowprofile 22.5 radial tires. |
| Axles | Five inch round, 22,500 lb. rating, 77-1/2″ track. |
| Brakes | Non-asbestos lining 16.5″ × 7″ quick change type,’S’ cam operated automatic slack adjuster. |
| ABS System | Two sensor, one modulator valve (2S/1M) system, no diagnostics tool. PCL4Trucks compatible system. |
| Oil Seals | Stemco Platinum Performance. |
ELECTRICAL
| Lights & Wiring | Color coded 12-volt sealed wiring system, internal ground, and special watertight molded connectors to accept sealed lamps. |
PAINT & FINISH
| Paint | Steel front impact guard is abrasive blasted, coated with zinc rich epoxy primer andwhite finish top coat |
| Undercoating | Flooring is pre-undercoated and crossmembers are dipped in a black color coating prior to installation. Landing gear and running gear areas painted with gray color non-hardening rust preventative. |
| Decals | D.O.T. approved Hyundai Translead logo conspicuity tape and FHWA inspection sticker. |
| Miscellaneous | Truck-Lite P/N 97960 registration cardholder on frontwall. White mud flaps with Hyundai logo mounted on rear of slider subframe. |
| Warranty | Limited five year warranty. |
along with insulated heaters for your hauling needs.
For More Information on parts,
call your local parts representative located on the
Contact Us page or call 780-447-1970