Replies: 11 comments 16 replies
-
|
morning matjack Release tested last night... |
Beta Was this translation helpful? Give feedback.
-
|
hey @ewc-beep sorry to hear that the new version doesn't work for you :( Can you please share your configuration so that I can try to reproduce? |
Beta Was this translation helpful? Give feedback.
-
|
me too, on 1.3.3 it workes fine but on 2.0.0 not |
Beta Was this translation helpful? Give feedback.
-
|
hey @thefirstkay sorry for the delay, if you can share the configuration that you have I can try supporting the update path, thank you very much!! |
Beta Was this translation helpful? Give feedback.
-
|
Would it be possible to add an option that only keeps the relay active in the presence of the card and deactivates it when it is removed? |
Beta Was this translation helpful? Give feedback.
-
|
@aplottier I don't think it's feasible to do what you want as most relays cannot be kept active for a long time otherwise they break. So just forgetting the card on the reader would break a relay :( What do you think? |
Beta Was this translation helpful? Give feedback.
-
|
Greetings, dear developers! Thanks for your unique project! I'm watching and trying to test. Testing on the wemos d1 mini board. Unfortunately, the latest firmware version has a critical problem - the inability of the controller to operate adequately in access point mode:
I can say with confidence that the problem appeared after commit [104a4d6] “Add timezone support”. I can also list some problematic issues:
|
Beta Was this translation helpful? Give feedback.
-
|
hey @snegokmf thank you very much for testing the latest release! Can you please try again with the files that you can find here: https://github.com/esprfid/esp-rfid/releases/tag/2.0.0.rc0 I have just updated them. For the UART readers I now have one to test and I'll try it to see what's up. Please follow this issue: #587 for updates. Thank you! |
Beta Was this translation helpful? Give feedback.
-
|
Greetings! A critical problem has been noticed in working with wiegand readers. Although I'm not very good at code, I think the problem lies in the reuse of lines to read File f = SPIFFS.open("/P/" + uid, "r"); and subsequent check conditions in the wiegandRead() function. Since the main check and reading is triggered in the rfidProcess() function. Here is part of the problem log. |
Beta Was this translation helpful? Give feedback.
-
|
can you please try again with the most recent version that you can find here: https://github.com/esprfid/esp-rfid/releases/tag/2.0.0.rc0 I think it should be fixed, let me know if it isn't though. I was able to reproduce and fix at some point. Thank you again :) |
Beta Was this translation helpful? Give feedback.
-
|
hi , dosen't work |
Beta Was this translation helpful? Give feedback.
-
|
hi, i have 2 problem 1-dosen't work rc522 in this version v2 , 2-after 2 days when i go to the user tab :Please wait while fetching data....... ,i cant add user ,edit user ... |
Beta Was this translation helpful? Give feedback.
-
|
hey @amirsholeh sorry for the delay here!
|
Beta Was this translation helpful? Give feedback.
-
|
Cool project, thanks to the author! ps..i found a solution: |
Beta Was this translation helpful? Give feedback.
-
|
Hello, the project is interesting and excellent. I have been using this project for the door of my house for 6 months and I want to express my opinion: first of all, traffic control is very important for me, and it would be great if the traffic information could be stored separately in one RAM. For example, he created a folder for user 1 and saved user 1's information in it. The next issue was that the device stopped working after a while and had to be reset, which I hope is fixed in the new version. |
Beta Was this translation helpful? Give feedback.
-
Recording.2024-03-27.145120.mp4Hello, forget the previous case, now this is the problem of the new version, what should I do? |
Beta Was this translation helpful? Give feedback.
-
|
hey @mmdjava sorry I missed this message before, did you manage to flash the device? |
Beta Was this translation helpful? Give feedback.
-
|
Hello, no, I couldn't and I'm still using the old version. Do you want to approve and publish version 2? |
Beta Was this translation helpful? Give feedback.
-
|
yes, I need to close two active PRs and have a round of testing with as many devices as possible, then I'll publish a V2. I have some time in these 2 weeks, it might happen in September :) |
Beta Was this translation helpful? Give feedback.
-
|
I think I'm programming esp wrong, can you post the correct way in the form of a video... |
Beta Was this translation helpful? Give feedback.
-
|
Hi thank for replay , this version has problem for read tag and very slow to load user page ,I'm using other version such as 1.3.3 or 1.3.7 but they have problem after 2 month doesn't load user page ( I have 180 user ) { --------------------user tag------------ |
Beta Was this translation helpful? Give feedback.
-
|
hay @amirsholeh can you please try with the latest I'm going to release a new release soon otherwise. |
Beta Was this translation helpful? Give feedback.
-
|
is there a possibility to update, if you have several doors like this, users can be synchronized or managed from one place, for example define one door as master and the others as slaves, and in this way manage users and privileges for each door which user should have access? |
Beta Was this translation helpful? Give feedback.
-
|
To have a similar setup we have a user DB in an external system and sync the users via MQTT. Daily we delete all the users and send back the full list. I have a Python script that does that from a Raspberry Pi that works as the master. If the script doesn't run for whatever reason or if the connection is absent you still have the users available from the previous day. |
Beta Was this translation helpful? Give feedback.
-
|
Hello thank you |
Beta Was this translation helpful? Give feedback.
-
|
Hello, I wanted to take a moment to express my sincere gratitude for this outstanding project. I recently had the opportunity to try out version 2.0, and while I found it to be incredibly impressive, I did encounter an issue with the RC522 module. Unfortunately, it doesn't seem to be working, as it's not recognizing any transponders, and all the values are returning as zero. Aside from this, I'm truly impressed, particularly with the planned integration into Home Assistant. I tested it in ioBroker, and the MQTT functionality is working flawlessly. Thank you again for all your hard work! Best regards. |
Beta Was this translation helpful? Give feedback.
- 800
Uh oh!
There was an error while loading. Please reload this page.
-
A release candidate for v2.0.0.
This discussion was created from the release v2.0.0.rc0.
Beta Was this translation helpful? Give feedback.
All reactions