- Research
- Open access
- Published:
Position-only synthesis of uniformly excited elliptical antenna arrays with minimum element spacing constraint
EURASIP Journal on Wireless Communications and Networking volume 2019, Article number: 253 (2019)
Abstract
Pattern synthesis of non-uniform elliptical antenna arrays is presented in this paper. Only the element positions of the antenna arrays are optimized by the combination of differential evolution (DE) and invasive weed optimization (IWO) to reduce the peak side lobe level (PSLL) of the radiation pattern. In order to avoid the overlap of the array elements, the minimum spacing of the adjacent elements is constrained. Also, the beam width of the radiation pattern can be constrained effectively. Three elliptical antenna arrays that have 8, 12, and 20 elements are investigated. The synthesis results show that the introduced method can present a good side lobe reduction for the radiation pattern. Compared with other optimization methods, the method proposed in this paper can obtain better performance.
1 Introduction
Designs of antennas have been paid more attention in the last few years [1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22]. Also, pattern synthesis of antenna arrays has become a traditional problem [6,7,8,9,10,11,12,13,14,15,16,17,18,19,20]. Moreover, much attention has been paid to the position-only synthesis of uniformly excited antenna arrays [6,7,8,9,10,11,12,13,14]. There are two kinds of uniformly excited antenna arrays. One is thinned array [6,7,8,9,10], which is to delete some array elements from a uniform array. These kinds of arrays can easily constrain the spacing of the adjacent elements. The other one is sparse antenna array which means that the array elements are randomly distributed along the antenna array [11,12,13,14]. Compared with thinned antenna arrays, sparse antenna arrays can obtain better simulation results. However, in the design of sparse antenna arrays, it is hard to constrain the size of the array aperture, number of the array elements, and the minimum spacing of adjacent elements at the same time.
In recent years, as the development of modern military and defense application, circular and elliptical antenna arrays have become more popular in wireless communication [15,16,17,18,19,20]. Compared with linear antenna arrays, the radiation patterns of the circular and elliptical antenna arrays can cover the entire space. In the design of circular and elliptical antenna arrays, synthesis of non-uniform arrays has been paid more attention [15,16,17,18,19,20]. In [15], genetic algorithms are proposed to determine optimum weights and element separations that provided a radiation pattern with peak side lobe level reduction with a fixed beam width. As is introduced in [16], Hierarchical Dynamic Local Neighborhood Based PSO (HDLPSO) algorithm is introduced into the design of non-uniform circular antenna arrays. Invasive weed optimization (IWO) is presented in [17] for the design of non-uniform, planar, and circular antenna arrays that can achieve minimum side lobe levels for a specific first null beam width. Biogeography-based optimization (BBO) is presented in [18] for the optimization of non-uniform circular antenna arrays, and the optimization results show that the synthesis of non-uniform circular antenna arrays using the BBO algorithm provides a SLL reduction better than that obtained by using a genetic algorithm, simulated annealing, and particle swarm optimization. In [20], synthesis of elliptical antenna arrays is introduced by using three different optimization algorithms (self-adaptive differential evolution method, biogeography-based optimization method, and firefly algorithm).
In order to avoid the overlap of the array elements, the space of the adjacent elements must be constrained in the design of elliptical antenna arrays. So, the purpose of this paper is to reduce the peak side lobe level of the radiation pattern by optimizing the positions of array elements that fulfil the minimum space constraint. The element positions are optimized by differential invasive weed optimization (DIWO), and low PSLLs of the radiation patterns are obtained. IWO has been widely used in the design of antennas [17, 21, 22]. Usually, IWO has better optimization results than the other optimization methods in the final error level. The rest of the paper is organized as follows: Method and experiment are introduced in Section 2. In Section 3, the mathematical formulation is given. The used optimization algorithms and the optimization steps are briefly described in Section 4. In Section 5, numerical results and comparisons are given. Finally, the paper is concluded in Section 6.
2 Method and experiment
The study of the paper is to introduce a new design method of non-uniform elliptical antenna arrays. First, the design of antenna arrays is expressed as an optimization problem. The structure of an elliptical antenna array is depicted, and the fitness function is given. Also, the formulations of the element positions that can constrain the minimum element spacing are deduced. Second, a modified invasive weed optimization is introduced. Then, it is used to solve the introduced optimization problems. The experiment is based on numerical simulations. To verify the effectiveness of the proposed method, synthesis results and comparisons are made by taking three different antenna arrays. Comparisons show that the proposed algorithm is more efficient than other algorithms. The analysis shows that the proposed method is useful and effective to solve the design of non-uniform elliptical antenna arrays.
3 Mathematical formulation
3.1 Structure and array factor of elliptical antenna array
The structure of an elliptical antenna array with N elements placed in the x-y plane is given in Fig. 1. The original point is at the center of the ellipse. The semi-major axis and semi-minor axis lengths are depicted by a and b, respectively. The eccentricity of the ellipse is e which is calculated by
The array factor of this elliptical antenna array is given by
where k = 2π/λ is the wave number. In and αn represent the excitation amplitude and phase of the nth element. ϕn is the angular position of the nth element in the x-y plane. ϕ is the azimuth angle which is measured from the positive x-axis. θ is the elevation angle measured from the positive z-axis. In the following design, the array factor in the x-y plane, i.e., θ = 90o, is considered. So, the array factor of the elliptical antenna array can be depicted by
If the direction of the main beam is φ0, the phase excitation of the nth array element can be given by
3.2 Fitness function
In order to obtain radiation patterns with minimum side lobe levels and a specific first null beam width (FNBW), the element positions of elliptical antenna arrays are optimized. The desired function can be given by
where w1 and w2 are the weighting factors. AFmax is the maximum value of |AF(Ï•)|. S is the side lobe area of the radiation pattern. The calculated first null beam width is defined by FNBWc, and the desired first null beam width is depicted by FNBWd.
In order to avoid the overlap of array elements, the minimum spacing of the adjacent elements is depicted by de. So, the objective function can be given by
where (xn, yn) is the position of the nth element which can be calculated by
In the following procedure, the problem is changed into a maximum problem. So, the fitness function can be defined by
3.3 Optimization of element positions
As is shown in Fig. 1, the length of the elliptical antenna array can be calculated by
The length that can allocate array elements is L − de. If array elements are allocated by the minimum spacing constraint de, the length of (N − 1)de is occupied. So, the remaining region over the array aperture to be optimized is given by [11]
In the determination of element positions, the position of the first element must be determined. The first element should be allocated in the area of [0, SP]. As is shown in Fig. 2, the length from O to the first element position along the ellipse can be depicted by
where r1 is the random number among the rang of [0, 1]. Then, N − 1 real random numbers among the range of [0, SP] are calculated by
\( {c}_{i-1}^{\prime }= SP\times {r}_i \), i = 2, 3, ⋯, N (12).
where ri, i = 2, 3, ⋯, N are real random numbers among the range of [0, 1]. Then, \( {c}_i^{\prime } \) are sorted in ascending order and a new vector C = [c1, c2, ⋯, cN − 1] is obtained, where c1 ≤ c2 ≤ ⋯ ≤ cN − 1. The length from O to the nth element position along the ellipse can be calculated by
If ln > L, ln is updated by
Then, ln is sorted in ascending order and the ultimate ln is obtained. It can be proved that the element spacing between nth element and (n + 1)th element is de + (cn + 1 − cn), n = 1, 2, ⋯, N − 1 which satisfies the minimum spacing constraint of (6).
After ln, n = 1, 2, ⋯, N are calculated, the angular position ϕn of the nth array element can be calculated by
4 Optimization algorithm
IWO and DE are intelligent algorithms which have been used in various kinds of optimization problems [21,22,23,24]. In order to improve the synthesis results, invasive weed optimization and differential evolution algorithm are combined for parallel computation. The IWO and DE has data exchange after m iteration steps. The newly introduced algorithm is called DIWO. The flowchart of this optimization method is given by Fig. 3. The optimization procedure can be expressed as follows:
Step 1. The parameter values of the antenna arrays and DIWO are given. A N × P–dimensional matrix r _ I and a N × d_max–dimensional matrix r _ D are chosen as the initial population for IWO and DE, respectively. Let iter = 1.
Step 2. The angular position of the array elements is calculated by (15).
Step 3. The radiation patterns of the antenna arrays are calculated by (3). The fitness value is defined by (8) which increases with the decrease of PSLL. The optimized element positions that can produce the best fitness value are preserved as the ultimate result.
Step 4. The optimization parameters r _ I and r _ D are updated by IWO and DE.
Step 5. If iter = 1 or iter = iter_max or mod (iter, m) = 0, go to step 6; otherwise, go to step 7. Where mod( ) is the modulus after division.
Step 6. Combine all the optimization population of IWO and DE. Choose the best p_max population as the new population of IWO. Choose the best d_max population as the new population of DE.
Step 7. Let iter = iter + 1, if iter < iter_max, go to step 2; otherwise, terminate iteration.
5 Results and discussion
In this section, several simulation results are given to show the feasibility and effectiveness of the proposed method. The parameters used in DIWO are given in Table 1. The minimum spacing constraint for the adjacent array elements is chosen as de = 0.15λ. The direction of the main beam is φ0 = 0o. The weighting factor w1 = 1, w2 = 3. The positions of the array elements are optimized to get radiation patterns with low side lobe levels. The algorithm is calculated 10 times, and the best result is preserved as the ultimate result.
5.1 Optimization result of 8-element antenna array
In the first example, pattern synthesis of elliptical antenna array that has 8 elements is introduced. The semi-major axis length a and eccentricity e of the ellipse are 0.5λ and 0.5, respectively. The desired first null beam width is chosen as FNBWd = 111o. The same array is optimized in [20] using self-adaptive differential evolution (SADE) technique, biogeography-based optimization (BBO) and firefly algorithm (FA). The PSLLs of the radiation patterns optimized by these three methods are − 19.12 dB, − 19.40 dB and − 19.43 dB, respectively. When the elements are uniformly placed on the ellipse, the PSLL of the radiation pattern is − 8.02 dB. Using the method proposed in this paper, the best PSLL of 10 calculation times obtained by DIWO is − 19.91 dB which is 0.48 dB lower than that optimized by FA. The beam width of the radiation pattern is 111.5°. The minimum spacing of the adjacent elements is 0.18λ which fulfils the minimum spacing constraint of (6). When the same array is optimized by DE and IWO, the best PSLLs are − 19.82 dB and − 19.89 dB, respectively. The radiation patterns synthesized by different algorithms are given in Fig. 4. Table 2 shows the element positions of the best synthesis result optimized by different algorithms. The worst PSLL of 10 calculation times optimized by DIWO is − 19.72 dB while the average PSLL is − 19.81 dB.
5.2 Optimization result of 12-element antenna array
In this example, synthesis result of elliptical antenna array that has 12 elements is given. The semi-major axis length and eccentricity of the ellipse are chosen as 1.15λ and 0.5, respectively. The desired first null beam width is 49°. The best PSLL optimized in [20] is − 10.37 dB by using SADE. The PSLL of the radiation pattern is − 3.82 dB when the elements are uniformly distributed. Using the method proposed in this paper, the best PSLL obtained by DIWO is − 10.65 dB. The beam width of the radiation pattern is 49.8°. The minimum spacing of the adjacent elements is 0.15λ. When the same array is optimized by DE and IWO, the best PSLLs are − 10.56 dB and − 10.58 dB, respectively. Figure 5 is the radiation patterns with minimum PSLL synthesized by different algorithms. Table 3 is the element positions of the elliptical antenna array optimized by different algorithms. In this example, the worst PSLL of 10 calculation times obtained by DIWO is − 10.36 dB and the average PSLL is − 10.56 dB.
5.3 Optimization result of 20-element antenna array
In [20], the 20-element elliptical antenna array is optimized by SADE, BBO, and FA. The semi-major axis length and eccentricity of the ellipse are chosen as 1.6λ and 0.5, respectively. The best PSLL is − 11.27 dB obtained by FA. In this paper, the same array is optimized by DIWO. The desired beam width of the radiation pattern is – 34°. The best PSLL of the radiation pattern is − 12.21 dB synthesized by DIWO. The beam width of the radiation pattern is 34.8°. The minimum spacing of the adjacent elements is 0.15λ. When the same array is optimized by DE and IWO, the best PSLLs are − 11.93 dB and − 11.96 dB, respectively. The radiation patterns synthesized by different algorithms are given in Fig. 6. Table 4 gives the element positions of the elliptical antenna array optimized by different optimization algorithms. In this synthesis example, the worst PSLL of 10 calculation times obtained by DIWO is − 11.77 dB and the average PSLL is − 11.87 dB.
6 Conclusions
Position-only synthesis of uniformly excited elliptical antenna arrays with minimum element spacing constraint has rarely been studied. When the array size and element number are given, it is hard to constrain the minimum spacing of the adjacent elements which is important in the design of antenna arrays. For the first time, pattern synthesis of non-uniform elliptical antenna arrays with minimum spacing constraint is introduced. The comparisons show that the design of non-uniform elliptical antenna arrays using the proposed method presents a good side lobe reduction in the radiation pattern for the optimized problem. Also, according to the real requirement of antenna array design, the minimum element spacing constraint can be set to other values.
Availability of data and materials
Not applicable.
Abbreviations
- BBO:
-
Biogeography-based optimization
- DE:
-
Differential evolution
- DIWO:
-
Differential invasive weed optimization
- HDLPSO:
-
Hierarchical Dynamic Local Neighborhood Based PSO
- IWO:
-
Invasive weed optimization
- PSLLs:
-
Peak side lobe levels
- PSO:
-
Particle swarm optimization
References
K.C. Hwang, A modified Sierpinski fractal antenna for multiband application. IEEE Antennas Wireless Propagation Lett. 6, 357–360 (2007)
C. Puente-Baliarda, J. Romeu, R. Pous, A. Cardama, On the behavior of the Sierpinski multiband fractal antenna. IEEE Trans. Antennas Propagation 46(4), 517–524 (1998)
J. Anguera, C. Borja, C. Puentea, Microstrip fractal-shaped antennas: a review. Paper presented at the 2nd European conference on antennas and propagation. (Edinburgh, 2007), pp. 11–16
E. Guariglia, Harmonic Sierpinski gasket and applications. Entropy 20(9), 714 (2018)
E. Guariglia, Entropy and fractal antennas. Entropy 18(3), 84 (2016)
R.L. Haupt, Thinned arrays using genetic algorithms. IEEE Trans. Antennas Propagation 42(7), 993–999 (1994)
Q.T. Óscar, R.I. Eva, Ant colony optimization in thinned array synthesis with minimum sidelobe level. IEEE Antennas Wireless Propagation Lett. 5, 349–352 (2006)
N. Pathak, G.K. Mahanti, S.K. Singh, et al., Synthesis of thinned planar circular array antennas using modified particle swarm optimization. Prog. Electromagnetics Res. Lett. 12, 87–97 (2009)
L.H. Abderrahmane, B. Boussouar, New optimization algorithm for planar antenna array synthesis. Int. J. Electron. Commun. 66, 752–757 (2012)
W.P.M.N. Keizer, Large planar array thinning using iterative FFT techniques. IEEE Trans. Antennas Propagation 57(10), 3359–3362 (2009)
K.S. Chen, Z.S. He, C.L. Han, A modified real GA for the sparse linear array synthesis with multiple constraints. IEEE Trans. Antennas Propagation 54(7), 2169–2173 (2006)
H. Chen, Q. Wan, Non-uniform array pattern synthesis using reweighted l1-norm minimization. Int. J. Electron. Commun. 67, 795–798 (2013)
O.M. Bucci, T. Isernia, A.F. Morabito, An effective deterministic procedure for the synthesis of shaped beams by means of uniform-amplitude linear sparse arrays. IEEE Trans. Antennas Propagation 61(1), 169–175 (2013)
B. Preetham Kumar, G.R. Branner, Design of unequally spaced arrays for performance improvement. IEEE Trans. Antennas Propagation 47(3), 511–523 (1999)
M.A. Panduro, A.L. Mendez, R. Dominguez, et al., Design of non-uniform circular antenna arrays for side lobe reduction using the method of genetic algorithms. Int. J. Electron. Commun. 60, 713–717 (2006)
P. Ghosh, J. Banerjee, S. Das, et al., Design of non-uniform circular antenna arrays-an evolutionary algorithm based approach. Prog. Electromagnetics Res. B 43, 333–354 (2012)
G.G. Roy, S. Das, P. Chakraborty, et al., Design of non-uniform circular antenna arrays using a modified invasive weed optimization algorithm. IEEE Trans. Antennas Propagation 59(1), 110–118 (2011)
U. Singh, T.S. Kamal, Design of non-uniform circular antenna arrays using biogeography-based optimization. IET Microwaves Antennas Propagation 5(11), 1365–1370 (2010)
A. Neyestanak, M. Ghiamy, M. Moghaddasi M, et al., An investigation of hybrid elliptical antenna arrays. IET Microwaves Antennas Propagation 2(1), 28–34 (2008)
A. Sharaqa, N. Dib, Position-only side lobe reduction of a uniformly excited elliptical antenna array using evolutionary algorithms. IET Microwaves Antennas Propagation 7(6), 452–457 (2013)
S.K. Mahto, A. Choubey, A novel hybrid IWO/WDO algorithm for nulling pattern synthesis of uniformly spaced linear and non-uniform circular array antenna. Int. J. Electron. Commun. 70, 750–756 (2016)
S. Karimkashi, A.A. Kishk, Invasive weed optimization and its features in electromagnetics. IEEE Trans. Antennas Propagation 58(4), 1269–1278 (2010)
A.R. Mehrabian, C. Lucas, A novel numerical optimization algorithm inspired from weed colonization. Ecol. Inform. 1, 355–366 (2006)
R. Stron, K. Price, Differential evolution-a simple and efficient heuristic for a global optimization over continuous spaces. J. Glob. Optim. 11(4), 341–359 (1997)
Acknowledgements
Not applicable.
Funding
This work was supported by the Natural Science Foundation of Shaanxi Province Department of Education (17JK0319) and Doctoral Scientific Research Foundation of Xi’an Polytechnic University (107020277) and Shaanxi Provincial Science and Technology Department (2018JQ4016).
Author information
Authors and Affiliations
Contributions
HG conceived the idea. HG and RJ complete the algorithm. HG, MD, and LZ wrote this paper. XZ contributed to the reviewing of the manuscript. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare that they have no competing interests.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Guo, H., Jing, G., Dong, M. et al. Position-only synthesis of uniformly excited elliptical antenna arrays with minimum element spacing constraint. J Wireless Com Network 2019, 253 (2019). https://doi.org/10.1186/s13638-019-1574-2
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13638-019-1574-2