Search Results (697)

This study introduces biodegradable nursery bags using poly(lactic acid) (PLA), a widely used biodegradable polymer, and spent coffee grounds (SCGs), a byproduct of the brewing process in the coffee industry. SCGs were oil-extracted to produce extracted spent coffee grounds (exSCGs), which were characterized by their physical properties, chemical functionality, and thermal behavior. The exSCGs were blended with PLA at loadings of 5, 10, and 15 wt%. Analysis showed that exSCGs retained 3–5 wt% residual coffee oil, exhibiting a lower surface area (1.1163 m²/g) compared to SCGs (1.5010 m²/g), along with a higher pore volume (1.148 × 10⁻³ cm³/g) and pore size (~410 nm). All PLA/exSCG bio-composite films displayed a light brown color, well-dispersed exSCG particles, and excellent UV light barrier properties, with transmittance reduced to 1–2%. The residual coffee oil acted as a plasticizer, reducing the glass transition temperature, melting temperature, and crystallinity with increasing exSCG content. Mechanical testing revealed enhanced flexibility compared to neat PLA. Soil burial tests showed increased biodegradability with higher exSCG content, supported by SEM analysis revealing cracks around exSCG particles. The PLA/exSCG blend containing 10 wt% exSCGs exhibited optimal performance, with a significant increase in melt flow index (from 4.22 to 8.17 g/10 min) and approximately double the melt strength of neat PLA, balancing processability and mechanical properties. This innovation provides a sustainable alternative to plastic nursery bags, addressing waste valorization and promoting eco-friendly material development for agricultural applications. Full article

A rapid microwave-assisted process minimizing waste was set up to produce bio-based benzoxazine-like monomers produced from vanillylamine and melamine. Without excessive purification, different viscous liquid precursors had a remarkable ability to form four strong and transparent different solid cross-linked thermosets, displaying lower curing temperatures under 130 °C. The long and strong adhesive performance of the cured materials was observed using glass slides or aluminum surfaces and they could become a good alternative to adhesive epoxy resin for metal surfaces. At the higher temperatures, these solids could act as efficient flame-retardants proven by thermogravimetric measurements. The best candidates gave a limiting oxidation index value of 41.9. In order to improve the intrinsic surface hydrophobicity of the phenolic resins, slight amounts of silica and iron oxide nanoparticles were dispersed in the polymer matrix, and finally mechanical resistance was pointed out. The most promising of our melamine-based resin was loaded with aluminum pigment to furnish a silver-colored paste ready for being cured to afford a robust solid, which does not undergo contraction or deformation. Full article

This study investigated the impact of different ageing containers on the volatile composition and quality of Negroamaro wine, a key variety from Apulia, Italy. Seven vessel types were evaluated: traditional Apulian amphorae (ozza), five types of oak barrels (American oak, French oak, European oak, a French + European oak and a multi-wood mix) and glass bottles as the control. The impact of the vessels was evaluated after 6 months of ageing through the characterization of phenolic, volatile and sensory profiles. Amphorae allowed a specific evolution of the wine’s primary aromas, such as fruity and floral notes, while enhancing volatile compounds like furaneol, which contributed to caramel and red fruit nuances, and also 3-methyl-2,4-nonanedione, a key compound related to anise, plum and premature ageing, depending on its concentration. This container also demonstrated effectiveness in stabilizing anthocyanin–tannin complexes, supporting color stabilization. Oak barrels allowed different outcomes to be obtained in terms of color stabilization, volatile profile, aroma and astringency. French oak exhibited the highest phenolic and tannin levels, enhancing anthocyanin stabilization and color intensity. European oak followed closely, while American oak excelled in color stabilization, with tannins less reactive to polymers. Mixed wood barrels showed lower phenolic extraction and the best astringency evolution. Full article

To investigate the influence of factors such as tourism, agriculture, and population density on the presence of microplastic (MP) content in aquatic environments and their associated ecological risks, Jingpo Lake, a remote high-mountain lake situated away from urban areas, was selected as the research subject. This study examined the abundance, types, sizes, colors, and polymer compositions of MPs within the water body, fish, and sediments. By considering variables, including fishing practices, agricultural activities, population dynamics, and vegetation cover, an analysis was conducted to unravel the spatial and temporal distribution of MPs concerning human activities, ultimately leading to an assessment of the ecological risks posed by MP pollution. The findings revealed that the average abundance of MPs in the lake’s surface water was recorded as (304.8 ± 170.5) n/m³, while in the sediments, it averaged (162.0 ± 57.45) n/kg. Inside the digestive tracts of fish, the MP abundance was measured at 11.4 ± 5.4 n/ind. The contamination of MPs within the aquatic environment of Jingpo Lake was found to be relatively minimal. Variations in MP loads across time and space were observed, with MPs predominantly falling within the size range of small planktonic organisms (50–1000 μm). Additionally, the prevalent colors of MPs in the water samples were white or transparent, constituting approximately 55.65% of the entire MP composition. Subsequently, they were black, red, and blue. This colors distribution were consistent across MPs extracted from fish and sediment samples. The chemical compositions of the MPs predominantly comprised PE (31.83%) and PS (25.48%), followed by PP (17.56%), PA (11.84%), PET (6.71%), EVA (4.56%), and PC (2.03%). Regarding the seasonal aspect, MP concentrations were highest during summer (46.68%), followed by spring (36.75%) and autumn (16.56%). The spatial distribution of MPs within Jingpo Lake’s water body, fish, and sediments was notably influenced by human activities, as confirmed by Pearson correlation coefficients. A strong association was observed between MP levels and water quality indicators such as ammonium nitrogen (NH₄-N), total phosphorus (TP), and chlorophyll-a (Chla), suggesting that human-related pollution contributed significantly to MP contamination. The diversity assessment of MP pollutants exhibited the highest variability in chemical composition (1.23 to 1.79) using the Shannon–Wiener Index. Subsequently, the diversity of colors ranged from 0.59 to 1.54, shape diversity from 0.78 to 1.30, seasonal diversity from 0.83 to 1.10, and size diversity from 0.44 to 1.01. The assessment results of ecological risk highlighted that the risk categories for MPs within the surface water, fish, and sediments of Jingpo Lake were categorized as I for the PHI and PLI and as “Minor” for the PERI. These relatively low-risk values were attributed to the predominantly low toxicity of the distributed MPs within the Jingpo Lake basin. Moreover, the results of the risk assessment were found to be interconnected with the distribution of the local population and agricultural activities around the sampling sections. Usage patterns of coastal land and population density were recognized as influential factors affecting MP loads within the water body, sediments, fish, and other components of the lake ecosystem. Full article

Spiropyran has an attractive and mysterious fluorescence switch and dual-color conversion characteristics, as it exhibits both aggregation-caused quenching (ACQ) in solvents and fluorescence enhancement in polymer matrices. The explanation for this phenomenon has always been of great controversy. Hence, the solvent effect on the emission of spiropyran (SP) was investigated in 16 solvents. By means of molecular orbital theory and the Jablonski diagram, several special parameters (e.g., Hansen solubility parameters and viscosity) were selected for this analysis, with excellent goodness of fit. Subsequently, the main factors that affected the blue shift, red shift, and luminescence efficiency of the emission of the ring-opened form merocyanine (MC) were found to be the hydrogen bonding and polarity, aggregation effect, and viscosity, respectively. A newly modified Jablonski diagram was proposed to clarify the emission behaviors of spiropyran influenced by solvent polarity and isomerization. Meanwhile, the solvent effect could also be extended to a solid polymer matrix (six kinds of polyethylene glycol (PEG) with different molecular weights), which is proposed to be defined as the generalized solvent effect. Accordingly, we have demonstrated that the unique fluorescence properties of spiropyran are dominated by the generalized solvent effect. The security information storage capacity of the simulated quick response (QR) code sensor combined with SP for anti-counterfeiting was significantly improved to six dimensions in taking advantage of the former theoretical analysis. Full article

(1) Background: The intra-oral behavior of clear thermoplastic dental materials can be influenced by various intrinsic and extrinsic factors. Aim: The purpose of this in vitro study was to evaluate the optical properties, color changes and whiteness variations of four thermoplastic polymers used for dental appliances, in a simulated oral environment. (2) Methods: Customized thermoformed specimens of four PETG thermoplastics were selected and investigated in this study: Leone [L], Duran [D], Erkodur [E] and Crystal [C]. The thermoplastic samples were divided into three groups related to pH values (neutral, acidic and basic). A period of 14 days was simulated. Five stages resulted: I. dessicated specimens; II. hydrated in artificial saliva; III. subsequent desiccated; IV. artificial aged; V. further dessicated. Optical CIE L*a*b* coordinates were determined and optical properties, like TP (translucency), OP (opalescence) values, color differences ΔE-NBS, white indexes in dentistry WI_D and white index differences ΔWI_D were calculated for all stages of the study, for each group of the materials. Statistical analyses were performed. (3) Results: Optical properties of PETG clear thermoplastic materials, like TP and OP, increase in a simulated oral environment and the changes become significant after artificial aging. Related to pH values, the optical behavior between the materials is significantly different. During artificial aging, the tested materials behave significantly differently in terms of optical properties. (4) Conclusions: After the simulated period of 14 days, TP and OP values increase, with a migration of the color towards red and yellow. Color changes in some cases even reach the level of extremely marked. Whiteness increases, and the differences are mostly perceptible, but partially exceed the limit of acceptability. Full article

Microplastics (MP) are ubiquitous contaminants in diverse environmental matrices, including biota. Urban birds, such as pigeons (Columba livia), are particularly vulnerable to MP exposure due to their scavenging habits and proximity to human activities. This study developed and applied a methodology to assess MP presence in pigeon feces, starting with a review of existing methods for extracting MPs from organic matrices. Of all the methodologies investigated, a method was established to be tested, varying the reagent, using pigeon feces collected from the Universidad Autónoma Metropolitana, Azcapotzalco Unit (UAM-A) and 15 virgin microplastics of five different types. Of both reagents, it was found that the method with 50% H₂O₂ presented better results (degradation of almost all organic matter and recovery efficiency of 93.33%). The selected method was optimized before being applied to feces collected from three sites in Mexico City (n = 10 samples per site). MPs were extracted using a digestion process with 50% hydrogen peroxide, flotation test with CaCl₂, staining with red Nile dye and vacuum filtration and analyzed by microscopy and FTIR. Concentrations ranged from 16.4 to 27.8 MP/g dry feces, with fragments (80%) and fibers (20%) being the predominant shapes. The most common colors were black (32%) and white (22%), the polymers identified included polystyrene and polyethylene and the most common size was < 1 mm (54%). These findings suggest that pigeons ingest MP during feeding, likely due to confusion with organic matter, highlighting the risks of urban plastic pollution to avian health. The ingestion of MPs could lead to malnutrition, organ damage, and ecosystem imbalances, underscoring the need for improved waste management in urban areas. This study provides evidence of the pervasive impact of plastic pollution in non-marine environments, demonstrating the potential of urban birds as bio-indicators of local contamination. Full article

Photodynamic therapy (PDT) is a light-activated chemical reaction used for the selective destruction of tissue. For this, various colorants may be applied, such as erythrosine (ERI), a dye already approved by the Food and Drug Administration (FDA) for various purposes. Although promising for PDT, ERI has a high hydrophilic profile that impacts its activity. To solve this, the combination of ERI with thermoresponsive and bioadhesive polymers may prove effective. Bio/mucoadhesive and thermoresponsive systems have attracted increasing interest in the development of novel pharmaceutical formulations for topical applications due to their ability to improve adhesion to the mucosa and prolong the residence time at the application site. In this study, systems based on poloxamer 407 (P407) in combination with cellulose derivatives (HPMC and NaCMC) were optimized, aiming at the topical release of ERI for PDT. The results demonstrated that the formulations containing low concentrations of cellulose derivatives exhibited greater adhesiveness and consistency at physiological temperature (37 °C), favoring the maintenance of the system at the application site. Regarding the gelation temperature (T_sol/gel), the formulations displayed values close to body temperature. The formulations with NaCMC showed a slightly higher T_sol/gel compared to HPMC ones, but it was adjustable by the polymer concentration. The addition of ERI influenced the mechanical and adhesive properties of the systems. In formulations containing HPMC, high concentrations of ERI increased bio/mucoadhesiveness, while in systems with NaCMC, the presence of ERI reduced this property. In both cases, the formulations maintained high consistency at 37 °C, contributing to the control of the active release at the application site. Rheological analysis revealed non-Newtonian behavior in all formulations, with greater consistency and elasticity at high temperatures. P407 was mainly responsible for the thermoresponsive transition from sol to gel, conferring desirable characteristics for topical application. Photodynamic activity was relevant in both formulations containing NaCMC and HPMC, which demonstrated greater capacity for degrading uric acid under light exposure. These systems are promising for the controlled release of drugs in photodynamic therapy, providing prolonged retention in the target tissue and maximizing the therapeutic efficacy of ERI. Full article

Color stability of acrylic resins is essential for preserving the aesthetic appearance of denture bases over time. This study explores how food pigments and thermal changes affect the color stability of commonly used denture base resins. Four acrylic resins were tested: three heat-cured acrylic resins with different characteristics (Zhermack^® Villacryl H Plus V2, H Plus V4, and H Rapid FN V4) and one self-cured acrylic resin (Zhermack^® Villacryl S V4). To simulate the oral environment, the resins underwent 1000 thermal cycles between 5 °C and 55 °C, followed by a 7-day immersion period in beverages such as coffee, red wine, a caramel-colored soft drink (cola), and distilled water (control), forming sixteen group of specimens (n = 5). Color changes (∆E) were measured using the VITA Easyshade V^® spectrophotometer, following the CIEDE2000 standard. The findings revealed that thermal aging caused noticeable color changes in all resins (p < 0.001). Red wine led to the most intense discoloration, followed by coffee. The caramel-colored soft drink caused moderate staining, while distilled water had a negligible effect. The type of polymerization did not affect the degree of discoloration, as no significant differences were found between the resins after exposure to beverages (p > 0.05). Overall, this study highlights how both internal and external factors impact the appearance of acrylic resins. Thermal aging can accelerate polymer degradation, while pigments in beverages cause visible staining. Among the tested beverages, red wine proved to be the most aggressive due to its high pigment concentration and low pH. These findings emphasize the need for improved material formulations to enhance the longevity and aesthetic performance of dentures. Full article

This study investigates the synthesis and application of acrylic–urethane hybrid polymer dispersions as advanced binders for leather finishing. Two polymerization techniques—seeded emulsion and miniemulsion—were used to produce hybrid polymer dispersions by varying the ratios of polyurethane (PU) and acrylic (AC). The synthesized dispersions, i.e., the hybrid polyurethanes, showed stable, uniform particle sizes, inferring good compatibility and interaction between the PU and AC phases, as confirmed by particle sizes, FTIR, and DSC analyses. The performance of the coating on leather surfaces was assessed by using standard physical tests, including rubbing fastness, flexing endurance, water spot resistance, and grain strength. The results showed that the hybrid polymers outperformed their individual PU and AC counterparts, particularly in terms of abrasion resistance and mechanical integrity. Of the two polymerization techniques, the seeded emulsion hybrids exhibited superior coating properties, providing greater resistance to cracking and abrasion under stress, improved grain strength, and better color retention during rubbing tests. These findings highlight the potential of acrylic–urethane hybrids, particularly those prepared via seeded emulsion polymerization, to address the limitations of traditional binders in high-performance leather applications. Full article

Polymer matrix composites (PMCs) often undergo aging as a result of ultraviolet (UV) radiation, which significantly impacts their performance and durability. This paper investigated the alterations in the microstructure and macroscopic properties of epoxy resin and its composite used in overhead wires during UV aging. Furthermore, the mechanism of UV aging for both resin and composite was revealed. The results showed that UV aging predominantly affected the properties of the surface layer resin. UV aging can induce molecular chain scission, which leads to resin weight change, color deepening, microcrack formation, a decline in mechanical properties, and other performance degradation behaviors under the combined action of many factors. With the increase in aging time, the weight change rate and hardness of the resin increased first and then decreased, while the mechanical properties of the composite decreased rapidly first and gradually tended to be constant. The bending strength and impact strength of the composite decreased by 6.0% and 12.8%, respectively, compared with the initial values. The purpose of this study is to comprehensively understand the UV aging behaviors of epoxy resins and their composites employed in overhead wires, and it also provides essential data for advancing the utilization and durability of epoxy resins and composites across aerospace, marine, and other outdoor applications. Full article

This study evaluated the strength, hardness, and color stability of 3D-printed denture base resins and compared the outcome with conventional heat-cured denture base resins after aging by thermocycling. A total of 72 specimens from conventional and 3D-printed materials were fabricated in different shapes and dimensions based on the mechanical and color tests performed. The specimens were divided into five groups: flexural, tensile, and compressive strengths (n = 20), hardness, and color stability (n = 6). In all these groups, half of the specimens were stored in a distilled water bath at 37 °C for 24 h, and the remaining half of the specimens were subjected to aging by thermocycling. The 3D-printed specimens demonstrated the highest means of tensile strength (32.20 ± 3.8 MPa), compressive strength (106.31 ± 4.07 MPa), and Vickers hardness number (24.51 ± 0.36), and the lowest means of flexural strength (54.29 ± 13.17 MPa) and color difference (ΔE = 2.18 ± 1.09). Conventional heat-cured specimens demonstrated the highest means of flexural strength (59.96 ± 8.39 MPa) and color difference (ΔE = 4.74 ± 2.37) and the lowest means of tensile strength (32.17 ± 9.06 MPa), compressive strength (46.05 ± 4.98 MPa), and Vickers hardness number (10.42 ± 1.05). Aging significantly reduced the flexural strength (−27%), tensile strength (−44%), and hardness (−7%) of 3D-printed resins in contrast to the conventional resin’s compressive strength (−15%) and color stability (p < 0.05). The 3D-printed resin had comparable flexural and tensile strength and significantly superior compressive strength, hardness, and color stability compared with conventional resins. Aging significantly and negatively affected the flexural strength, tensile strength, and hardness of 3D-printed resin. Full article

Recycling end-of-life wind turbines poses a significant challenge due to the increasing number of turbines going out of use. After many years of operation, turbines lose their functional properties, generating a substantial amount of composite waste that requires efficient and environmentally friendly processing methods. Wind turbine blades, in particular, are a problematic component in the recycling process due to their complex material composition. They are primarily made of composites containing glass and carbon fibers embedded in polymer matrices such as epoxies and polyester resins. This study presents an innovative approach to analyzing and valorizing these composite wastes. The research methodology incorporates integrated processing and analysis techniques, including mechanical waste treatment using a novel compression milling process, instead of traditional knife mills, which reduces wear on the milling tools. Based on the differences in the structure and colors of the materials, 15 different kinds of samples named WT1-WT15 were distinguished from crushed wind turbines, enabling a detailed analysis of their physicochemical properties and the identification of the constituent components. Fourier transform infrared spectroscopy (FTIR) identified key functional groups, confirming the presence of thermoplastic polymers (PET, PE, and PP), epoxy and polyester resins, wood, and fillers such as glass fibers. Thermogravimetric analysis (TGA) provided insights into thermal stability, degradation behavior, and the heterogeneity of the samples, indicating a mix of organic and inorganic constituents. Differential scanning calorimetry (DSC) further characterized phase transitions in polymers, revealing variations in thermal properties among samples. The fractionation process was carried out using both wet and dry methods, allowing for a more effective separation of components. Based on the wet separation process, three fractions—GF1, GF2, and GF3—along with other components were obtained. For instance, in the case of the GF1 < 40 µm fraction, thermogravimetric analysis (TGA) revealed that the residual mass is as high as 89.7%, indicating a predominance of glass fibers. This result highlights the effectiveness of the proposed methods in facilitating the efficient recovery of high-value materials. Full article

Abstract: Quantum dot–polymer composites have the advantages of high luminescent quantum yield (PLQY), narrow emission half-peak full width (FWHM), and tunable emission spectra, and have broad application prospects in display and lighting fields. Research on quantum dots embedded in polymer films and plates has made great progress in both synthesis technology and optical properties. However, due to the shortcomings of quantum dots, such as cadmium selenide (CdSe), indium phosphide (InP), lead halide perovskite (LHP), poor water, oxygen, and light stability, and incapacity for large-scale synthesis, their practical application is still restricted. Various polymers, such as methyl methacrylate (PMMA), polyethylene terephthalate (PET), polystyrene (PS), polyvinylidene fluoride (PVDF), polypropylene (PP), etc., are widely used in packaging quantum dot materials because of their high plasticity, simple curing, high chemical stability, and good compatibility with quantum dot materials. This paper focuses on the application and development of quantum dot–polymer materials in the field of backlight displays, summarizes and expounds the synthesis strategies, advantages, and disadvantages of different quantum dot–polymer materials, provides inspiration for the optimization of quantum dot–polymer materials, and promotes their application in the field of wide-color-gamut backlight display. Full article

Colored polymer microspheres have attracted significant attention in both academia and industry due to their unique optical properties and extensive application potential. However, achieving a uniform distribution of dyes within these microspheres remains a challenge, particularly when heavy concentrations of dye are used, as this can lead to aggregation or delamination, adversely affecting their application. Additionally, many dyes are prone to degradation or fading when exposed to light, heat, or chemicals, which compromises the long-term color stability of the microspheres. Consequently, the preparation of colored polymer microspheres with high stability continues to be a significant challenge. This review offers a comprehensive overview of the preparation techniques for colored polymer microspheres and their dyeing mechanisms, introducing the fundamental concepts of these microspheres and their applications in various fields, such as biomedicine, optical devices, and electronic display technologies. It further presents a detailed discussion of the different preparation methods, including physical adsorption, chemical bonding, and copolymerization. The advantages, limitations, and potential improvements of each method are explored, along with an analysis of the interactions between dyes and the polymer matrix, and how these interactions influence the properties of the microspheres, including their color uniformity, stability, and durability. Finally, the review discusses future perspectives on the development of colored polymer microspheres, highlighting the advancement of novel materials, innovations in preparation technology, and the exploration of potential new application areas. Full article